Water Heater Repair in Houston, TX
We repair leaking, noisy, gas, electric, tank, and tankless water heaters.
A wet threshold outside a utility closet and a dry hallway followed by a cold shower are both often reported as a water-heater problem, but they lead us to different faults. Water at the base of a tank, beneath a relief pipe, or below a wall-mounted unit calls for leak tracing; cold water with a dry floor calls for a fuel, power, control, or heating check. We handle both conditions across Houston, West University Place, Southside Place, and Bellaire.
We check for active water around the tank, pan, supply lines, drain valve, and temperature-pressure relief discharge pipe before working on the heater controls. A dry loss of hot water can sometimes wait for a scheduled repair, but a growing puddle, gas smell, or water near an electrical connection should not wait because a tank seam, valve, or connection can damage nearby flooring and create an electrical or ignition hazard.
No hot water or puddle
“No hot water” can describe a tripped electrical circuit, failed heating element, burned-out igniter, pilot problem, thermostat fault, or control-board issue. “The hot water runs out after one shower” often points toward a heating problem, sediment inside a tank, a dip tube issue, or a unit that is not recovering as it should. “My water heater is making a popping or rumbling noise” commonly comes with mineral buildup at the bottom of a tank.
“Water heater leaking from the bottom” can come from a drain valve, a supply connection, a relief discharge pipe, condensation, or the tank itself. A pilot that will not stay lit, a blinking error code, rusty water, and a sulfur-like smell are also useful descriptions when you call. Those symptoms can sound alike from the kitchen or bathroom, but the parts, access, and labor behind each fault are different once we inspect the heater.
Tank and burner inspection
During a tank and burner inspection, we read the model plate, identify the fuel or electrical supply, and examine the tank shell, vent pipe, shutoff valve, fittings, drain valve, and relief line. We isolate the electrical circuit or gas supply before checking the thermostat, heating elements, igniter, pilot assembly, burner, sensors, and wiring. An accessible diagnostic check commonly takes 30 to 60 minutes, while draining a tank or tracing a concealed water path can add time to the visit.
We can often replace an accessible thermocouple, igniter, thermostat, heating element, relief valve, drain valve, or supply connector during the same callout once the correct part is confirmed. We also check the temperature setting, which is commonly set around 120°F, and look for water pressure conditions that may affect a relief valve or expansion tank. A failed tank shell, an inaccessible pipe connection, or an electronic control that must be ordered is booked for follow-up work rather than forced into an incomplete repair.
Shutoff valves and access
Part age and availability affect the work on a water heater because a discontinued control, older burner assembly, or uncommon heating element may need to be matched from the model number rather than selected by appearance. A newer, readable model plate can make a compatible thermostat, igniter, or element easier to identify. Corrosion at the tank nipples, fittings, or drain valve can also turn a simple replacement into a longer repair.
Access changes the scope when a heater sits in a tight closet, attic platform, cabinet, or pan with limited room around the supply lines and vent. A cold-water shutoff that has seized may need additional work before we can safely isolate the heater and remove a valve or connector. A special-order control, a vent alteration, or work requiring local permit sign-off adds steps beyond replacing an accessible service part.
Model plate and access
Before calling, find the model and serial number on the manufacturer plate, usually on the side of a tank or behind the front cover of a tankless unit. Tell us whether the heater uses gas or electricity and whether the unit is in a garage, closet, attic, utility room, or exterior wall cabinet. The approximate age of the heater and any error code on the display help us identify likely controls and replacement parts.
Let us know whether water is actively running from the tank, relief pipe, drain valve, or a connection above the unit. Mention if the access door, attic opening, shutoff valve, or electrical panel is blocked by shelving, storage, or a finished wall. Call houston plumbing company at (210) 405-1525, because a tank leak can worsen damage to the pan, floor, framing, and nearby cabinet materials while it waits.
When we are open
Mon–Sun Open 24 hours
Next
Next: toilet repair, or back to the home page.
