Skip to content
houston plumbing company (210) 405-1525
04

Toilet Repair in Houston, TX

Toilet repairs for running tanks, weak flushes, leaks, and clogged bowls.

A plumber standing with arms folded in a utility room in front of a water heater, copper pipework and an expansion tank running above it, an open tool bag beside him

A toilet that needs two flushes, refills after every use, or leaves a small puddle at the base can become more than an inconvenience over a week or month. A running fill valve keeps cycling water through the tank, while a slow leak at the bowl base can soak grout, vinyl, or the subfloor beneath the bathroom floor. A weak flush can also leave waste in the trapway and turn a usable fixture into one that backs up more easily.

A loose handle or worn flapper may seem minor, but tank parts rarely improve with continued use. We check the tank, bowl, supply line, shutoff valve, and floor around the toilet to find the source of the fault. Most toilet repair work should not be left waiting when water is running, leaking, or failing to clear the bowl, because wasted water and floor moisture can continue long after the bathroom is empty.

Toilet keeps running

A toilet that keeps running is one of the most common calls we receive. Water may hiss into the tank, trickle into the bowl, or cause the fill valve to switch on every few minutes without anyone flushing. A toilet that will not flush, has a handle that moves without lifting the flapper, or fills unusually slowly points to a different group of tank parts.

Water around the toilet base can come from a loose supply connection, condensation, a leaking tank bolt, or a failed seal below the bowl. A sewer smell near the bowl, a wobbling base, or water appearing only after a flush can indicate a problem at the wax ring or flange rather than inside the tank. Running water, poor flushing, and a wet floor can look similar from the doorway, but each involves different parts, labor, and repair costs once we inspect the fixture.

Tank and bowl inspection

A tank and bowl inspection starts with the flush handle, flapper, fill valve, overflow tube, tank bolts, supply connector, shutoff valve, and bowl base. We flush the toilet more than once, watch the refill cycle, check for water entering the overflow tube, and look for moisture at the floor and behind the tank. We can also measure supply pressure, which is commonly kept within a residential range of 40 to 60 psi, and check whether a pressure issue is affecting the fill valve.

A basic inspection commonly takes 20 to 40 minutes, depending on cabinet access, the toilet location, and whether water is visible at the base. We can usually replace a worn flapper, fill valve, trip lever, tank-to-bowl gasket, or supply connector during the same visit when the needed part is available. Bowl removal, flange repair, a seized shutoff valve, a cracked porcelain tank, or a special-order flush valve may need a separate appointment because those repairs require more access, parts, or drying time.

Flapper, shutoff, and flange

The flapper, fill valve, and flush valve affect the scope of a tank repair. Rubber flappers can harden, warp, or collect mineral buildup, while an older fill valve may no longer shut off cleanly after the tank reaches its water line. A toilet with an uncommon flush valve size, a specialty color, or a manufacturer-specific tank component can require a matching part rather than a standard replacement.

Access also changes the work at the toilet. A shutoff valve that turns freely and a clear path around the bowl make a repair more straightforward than a valve that has seized behind a vanity or a toilet installed tightly against tile and cabinetry. A leak at the flange can involve lifting the bowl, replacing the seal, checking the flange condition, and addressing a soft or damaged section of floor before the toilet is reset.

Tank model and room

The tank model number can help us bring the correct flapper, fill valve, trip lever, or flush valve parts. A manufacturer name and model marking may be printed inside the tank, beneath the lid, or on the back of the porcelain. Let us know which bathroom contains the toilet and whether the bowl is running, leaking at the base, clogged, or unable to flush now.

A photo of the tank interior, the shutoff valve, and the floor around the bowl can show access restrictions before we arrive. Mention whether the toilet rocks, whether water appears only after flushing, and whether a vanity, wall, or cabinet limits space beside the fixture. Call (210) 405-1525 before a running tank continues cycling water or a base leak has more time to stain and soften the bathroom floor.

When we are open

Mon–Sun Open 24 hours

Next

Next: faucet repair, or back to the home page.