Faucet Repair in Houston, TX
Faucet repairs for drips, low flow, loose handles, and leaks in Houston.
A loose faucet handle, a cleaned aerator, or a careful turn on the knob is usually the first thing people try. Those steps are sensible when a kitchen or bathroom fixture starts dripping or delivers less water than usual. A handle screw can loosen, mineral scale can block an aerator screen, and a worn washer may briefly respond to a gentler turn. The problem usually returns when the cartridge, stem, valve seat, or supply connection is the actual source of the fault.
We repair faucet components rather than treating every drip as the same problem. Water around the base can come from a spout seal, while water in the cabinet may come from a supply line, shutoff valve, or faucet body. A slow drip may allow time for a planned repair if the sink basin drains normally and the cabinet stays dry, but an active leak below the counter should not wait because water can swell cabinet panels, damage flooring, and reach the wall behind the fixture.
Faucet drip and low flow
“My faucet keeps dripping,” “the handle turns but no water comes out,” and “the water pressure is weak at one sink” describe different faults. A drip from the spout after the handle is off often points to a cartridge, stem, washer, or valve seat. Low flow at one fixture can be an aerator packed with mineral debris, a blocked spray head, a kinked supply line, or a partly closed shutoff valve. A faucet handle that spins, feels loose, or will not move through hot and cold positions can involve the handle adapter, retaining nut, cartridge, or internal stem.
Water pooling at the faucet base is another common call, especially after the fixture has been running. A worn O-ring around a swivel spout can leak onto the countertop, while a failed seal beneath the faucet can send water under the sink. Water beneath the cabinet can also appear only when the faucet is on, which makes the supply hoses and shutoff connections important to inspect. Similar sounds and leaks can hide very different repairs, so the part, access, and labor involved can differ once we inspect the fixture.
Faucet valve inspection
During a faucet valve inspection, we run the hot and cold sides, watch the spout and base, and inspect the cabinet for moisture at the hoses, stops, and drain opening. We remove the aerator when low flow is limited to one outlet, then check the screen and flow from the spout without it. We also test handle movement, identify the cartridge or stem style, and check that the shutoff valves hold when closed. Water pressure may be checked when more than one fixture has a flow concern; residential plumbing pressure is commonly kept within a range of 40 to 80 psi.
A straightforward inspection and accessible repair can often be completed during the same visit when the needed cartridge, O-ring, washer, aerator, or supply line is available. Removing a handle, exposing the retaining clip or nut, and fitting a replacement part commonly takes longer when corrosion has bonded the pieces together. A seized shutoff valve may need separate work before a faucet can be safely opened, and a proprietary cartridge or discontinued trim part may need to be ordered. We explain the condition of the valve body and the available repair path before replacing parts.
Cartridge age and shutoff valves
Cartridge age and shutoff valve condition are two major factors in faucet repair work. A common cartridge with clear access beneath the sink is usually more direct than a discontinued cartridge that must be identified from a maker’s plate or matched from the removed part. Mineral scale can lock a cartridge into the faucet body, and corrosion can damage a retaining clip or stem during removal. A faucet installed behind a deep sink bowl, disposal, pullout drawer, or crowded cabinet also takes more time to reach and test.
A shutoff valve that closes fully lets us isolate the fixture without disturbing nearby plumbing. A seized, leaking, or missing shutoff changes the scope because the water supply must be controlled before the faucet body can be opened. Finish material matters as well: some older handles, trim rings, and specialty spouts require careful removal to avoid damaging a surface that cannot be readily matched. Parts that are not locally available, including specific cartridges and side-spray assemblies, require a return visit after the correct component is obtained.
Model number and fixture room
Before calling about a faucet, check which room contains the fixture and whether the leak is at the spout, the handle, the base, or inside the cabinet. A model number or maker name is often printed on the faucet body, beneath a handle cap, on a spray head, or in the installation paperwork. Let us know the approximate age of the fitting, whether the faucet has one handle or two, and whether a pullout hose or side sprayer is connected. A photo of the handle and the space beneath the sink can show the cartridge style, supply hoses, shutoff valves, and cabinet access. Tell us if water is running now or if the fixture can be isolated at the shutoff valve. Call houston plumbing company at (210) 405-1525, because a cabinet leak can worsen from a small faucet fault into damaged wood, flooring, and wall material.
When we are open
Mon–Sun Open 24 hours
Next
Next: water heater installation, or back to the home page.
